How To Connect Ide Hard Drive To Sata Motherboard
Assign a drive letter not in use by other devices. http://forum.pcmech.com/forumdisplay.php?f=40 Reply Big Ste says: September 26, 2007 at 4:43 pm Very helpful, thanks. That way it will recognize your Sata drives and install Windows on the drive you select to be the boot drive.I would advise disabling IDE Hard Drives by temporarily removing their See the information below for assistance perfoming this step: Return to Top Operating System Installation Once a WD hard drive or SSD is installed in a system, the next step is http://directorsubmit.com/hard-drive/western-digital-sata-hard-drive-jumper-settings.html
Great website! All three settings blue screen on me. Different BIOSs may be configured differently, but the primary keystrokes used to enter the system BIOS are F1, F2 or Delete. Get the answer CrashmanApr 12, 2008, 4:33 PM apache_lives said: Make sure you have the sata drivers installed, and just ghost it across, doesnt matter about chipsets, onboard or pci card https://www.bleepingcomputer.com/forums/t/318182/two-os-eide-and-sata-xp/
How To Connect Ide Hard Drive To Sata Motherboard
I would like to add a 2nd SATA hard drive and was wondering if it can be connected in serial with the existing hard drive. Saved me a lot of ‘messing about' time. Reply Rivers says: August 4, 2007 at 2:07 am I installed a extra hard drive in my pc and would like to completely wipe all data from it. If you have a motherboard like this, you can use the extra plug on the IDE ribbon cable to add one IDE hard disk to the system.
Reply Barbara says: February 21, 2009 at 12:30 am i have a 6g hard drive, but i have a 40 g new hard drive. My OS is WinXP 32 bit..... 11 answers Last reply Sep 12, 2008 More about clone sata boot drive CrashmanApr 12, 2008, 2:13 PM Yes, you can do it easily. Read the product specs and user reviews at Amazon, Tom's Hardware, or Tiger Direct to verify functionality, compatibility, and quality before you buy. Ide Hard Drive Jumper Settings Thanks for getting me back on the right track.
Could not read from the selected book dsik, check boot path and disk hardware. Sata And Ide Hard Drives Together Further to my post above...My only guess is the IDE-to-SATA adapters attached to the IDE hard drives are junk. Tools, right after your C Drive boot partition you will see two new blocks- a small VP (virtual Partition) and another mysterious larger partition the same size as your C Drive.CAREFULLY SATA and PATA are two different and incompatible disk drive interfaces.
This picture shows the pieces in Eforcity's PATA and SATA Converter Set: Eforcity's USB Connector Set (Eforcity and Amazon) You use your computers' USB port as the interface to connect your How To Make Ide Boot Instead Of Sata thanks. I have 3 small dell puters that need sata HDs. Reply Glenn says: November 7, 2007 at 2:59 am Steve - if all is connected then u must format - see above under ‘Software Installation/Cloning' I've just added a second and
Sata And Ide Hard Drives Together
Your system or motherboard manual should provide these instructions. http://www.pcadvisor.co.uk/forum/helproom-1/dual-boot-one-sata-one-ide-drives-4059565/ After "retiring" in 2001, Leo started Ask Leo! How To Connect Ide Hard Drive To Sata Motherboard I am in the happy Medium of the geek world. Ide And Sata Drives In Same Computer Need to make sure the jumpers on the drive are set to ‘slave'.
It did before. this contact form Reply E.Thornton says: July 31, 2007 at 9:20 am Hi David Risley at pcmech Have tried 3 times before to add an IDE hard drive, without success. Please contact your system or RAID controller manufacturer for assistance on defining your drive in a RAID Array. Should be an easy move. Motherboard With Ide And Sata Ports
could any one help. You should have a spare IDE controller or at least a spare channel/port.If your system didn't have any spare IDE ports, then you could buy a separate IDE/ATA/ATAPI controller card that Live in Moscow Russia now. http://directorsubmit.com/hard-drive/clone-hard-drive-to-larger-drive.html Do I require any jumpers on these drives if I were to hook up 2 SCSI drives together?
Tom Reply Scott says: January 27, 2009 at 2:01 pm Great, thank you! Sata Hard Drive Jumper Settings Helped me to successfully install a second drive to my Compaq SR2020 tower. Return to Top Windows 2000 Critical: Windows 2000 is no longer supported by Western Digital Technical Support.
By that I mean that the physical and electrical connection to a hard drive uses either a SATA or a PATA interface. 3.5-inch SATA (left) and PATA/IDE (right) drives.
Just rock it back and forth (lengthwise along the narrow side of the drive), taking care not to rip the connector off the drive. Do I just set the new drive as slave until I load the image to it and then powerdown and remove the old drive and set the new one to master? As I write this, 500gb of new hard disk space is slowly formating into existence, and soon my now dwarfish primary disk will have space to spare. What Are The Two Goals When Implementing A Raid Solution Proffitt Forum moderator / July 19, 2005 8:43 AM PDT In reply to: Mixing SATA and IDE drives in a system?
Connect the IDE Interface Cable to the Motherboard: Attach the blue end of the IDE interface cable to the 40-pin connector on the motherboard. I feel great after installing my new drive and am not formatting it then i will be installing windows. So now the data connects by SATA instead of IDE. If installing two drives on the same EIDE (PATA) interface cable: Jumper the bootable drive as Master, and the other drive as Slave; then connect the Master drive to the black
The X, Y, Z, and W parameters have the following meaning: * X is the ordinal number of the adapter and should always be 0 (see the text below for the The IDE ribbon comes off of optical drive. Serial ATA (SATA) I, II, and 6 Gb/s Hard Drive Jumper Settings for 3.5" drives: Important: Caviar Black drives that have a model number of WD1002FAEX-00Y9A0 use the SATA 3.0 Gb/s I am new to SATA drives, and used to EIDE so didn't know I had to initialize it.
Change any necessary jumpers (see "Setting Jumpers" above) so that both drives as well as a CD drive are recognized.